Top of page

Photo, Print, Drawing Woolsey Bridge, County Road 1408, Woolsey, Washington County, AR

[ Drawings from Survey HAER AR-63  ]

More Resources

[ Data Pages from Survey HAER AR-63  ]

About this Item

Title

  • Woolsey Bridge, County Road 1408, Woolsey, Washington County, AR

Names

  • Historic American Engineering Record, creator
  • State of Arkansas
  • University of Arkansas
  • Denham, Elam, project manager

Created / Published

  • Documentation compiled after 1968

Headings

  • -  steel truss bridges
  • -  transportation
  • -  bridge construction
  • -  Arkansas -- Washington County -- Woolsey

Notes

  • -  Significance: The Woolsey Bridge that crosses the West fork of the White River in Washington County, Arkansas, was built in 1947. This bridge is a steel drive through Parker Truss type bridge. The dimensions of the Woolsey Bridge are 301'0" x 16'0" and has only one lane. It has two arches in each side with each spanning 150'6" in length. The driving surface of the bridge is a four inch (4") concrete slab on a wire mesh and fabric base. There are I-Beams running in two directions supporting the slab of the bridge, which are 6-10" x 4 1/2" x 3/8" at 2'2' on center, spanning the length of the bridge and supporting the slab. Spanning the width of the bridge and supporting the I-Beams is 1-18" x 6" x 1/2" typical at each panel. Each panel is 18'10" in length for a total of sixteen panels. There are three concrete piers that support the bridge, one at each end and one at the mid-span of the structure. At the west pier there is a pinned connection as opposed to the east pier, which used a rocker connection. In the mid-span pier both a rocker and a pinned connection are used. The structure height from top of the slab to the water is approximately 13'0". The height from the top of the slab to the highest point on the is 26'-10'. In the mid-thirties there became an awakening to streamline bridges, by using shallower trusses. This was achieved in two ways. The first being a change from cast iron to steel which reduced the amount of material required, since less material was needed this also lowered the cost of the bridge. With the use of less materials this decreased the loads on the bridge. The second way was by using elements of a plate, two C-channels, and a shallow ribbon of steel. This ribbon of steel acts as a stiffener between the C-channels and the plate. The method used on the Woolsey Bridge solved several problems in the construction. All parts of the bridge could be hot rolled then punched or drilled at a steel plant, then shipped to the site. This method of fabricating the parts and shipping them to the site for assembly proved to be more cost effective. Because of the mountain area this allowed the parts to be shipped in with a great deal of ease. With the tight building constrictions of the area cranes could not be used, instead pulleys, block and tackles were used to hoist the elements of the bridge in place. Since all elements had to be assembled on site hot rivets were used to connect the structure.
  • -  Unprocessed Field note material exists for this structure: N932
  • -  Survey number: HAER AR-63

Medium

  • Measured Drawing(s): 5

Call Number/Physical Location

  • HAER AR-63

Source Collection

  • Historic American Engineering Record (Library of Congress)

Repository

Control Number

  • ar0135

Rights Advisory

Online Format

  • image
  • pdf

Rights & Access

The Library of Congress does not own rights to material in its collections. Therefore, it does not license or charge permission fees for use of such material and cannot grant or deny permission to publish or otherwise distribute the material.

Ultimately, it is the researcher's obligation to assess copyright or other use restrictions and obtain permission from third parties when necessary before publishing or otherwise distributing materials found in the Library's collections.

For information about reproducing, publishing, and citing material from this collection, as well as access to the original items, see: Historic American Buildings Survey/Historic American Engineering Record/Historic American Landscape Survey (HABS/HAER/HALS) Collection - Rights and Restrictions Information

Obtaining Copies

If Digital Images Are Displaying

You can download online images yourself. Alternatively, you can purchase copies of various types through Library of Congress Duplication Services.

HABS/HAER/HALS materials have generally been scanned at high resolution that is suitable for most publication purposes (see Digitizing the Collection for further details about the digital images).

  • Photographs--All photographs are printed from digital files to preserve the fragile originals.
    • Make note of the Call Number and Item Number that appear under the photograph in the multiple-image display (e.g., HAER, NY,52-BRIG,4-2).
    • If possible, include a printout of the photograph.
  • Drawings--All drawings are printed from digital files to preserve the fragile originals.
    • Make note of the Survey Number (e.g., HAER NY - 143) and Sheet Number (e.g., "Sheet 1 of 4"), which appear on the edge of the drawing. (NOTE: These numbers are visible in the Tiff "Reference Image" display.)
    • If possible, include a printout of the drawing.
  • Data Pages
    • Make note of the Call Number in the catalog record.

If Digital Images Are Not Displaying

In the rare case that a digital image for HABS/HAER/HALS documentation is not displaying online, select images for reproduction through one of these methods:

  • Visit the Prints & Photographs Reading Room and request to view the group (general information about service in the reading room is available at: https://aj.sunback.homes/rr/print/info/001_ref.html). It is best to contact reference staff in advance (see: https://aj.sunback.homes/rr/print/address.html) to make sure the material is on site. OR
  • P&P reading room staff can provide up to 15 quick copies of items per calendar year (many original items in the holdings are too old or fragile to make such copies, but generally HABS/HAER/HALS materials are in good enough condition to be placed on photocopy machines). For assistance, see our Ask a Librarian page OR
  • Hire a freelance researcher to do further selection for you (a list of researchers in available at: https://aj.sunback.homes/rr/print/resource/013_pic.html).
  • You can purchase copies of various types, including quick copies, through Library of Congress Duplication Services (price lists, contact information, and order forms for Library of Congress Duplication Services are available on the Duplication Services Web site):
    • Make note of the Call Number listed above.
    • Look at the Medium field above. If it lists more than one item:
      • The entire group can be ordered as photocopies or high-quality copies.
      • All the items in a particular medium (e.g., all drawings, all photographs) can be ordered as photocopies or high-quality copies.

Access to Originals

Please use the following steps to determine whether you need to fill out a call slip in the Prints and Photographs Reading Room to view the original item(s). In some cases, a surrogate (substitute image) is available, often in the form of a digital image, a copy print, or microfilm.

  1. Is the item digitized? (A thumbnail (small) image will be visible on the left.)

    • Yes, the item is digitized. Please use the digital image in preference to requesting the original. All images can be viewed at a large size when you are in any reading room at the Library of Congress. In some cases, only thumbnail (small) images are available when you are outside the Library of Congress because the item is rights restricted or has not been evaluated for rights restrictions.
      As a preservation measure, we generally do not serve an original item when a digital image is available. If you have a compelling reason to see the original, consult with a reference librarian. (Sometimes, the original is simply too fragile to serve. For example, glass and film photographic negatives are particularly subject to damage. They are also easier to see online where they are presented as positive images.)
    • No, the item is not digitized. Please go to #2.
  2. Do the Access Advisory or Call Number fields above indicate that a non-digital surrogate exists, such as microfilm or copy prints?

    • Yes, another surrogate exists. Reference staff can direct you to this surrogate.
    • No, another surrogate does not exist. Please go to #3.
  3. If you do not see a thumbnail image or a reference to another surrogate, please fill out a call slip in the Prints and Photographs Reading Room. In many cases, the originals can be served in a few minutes. Other materials require appointments for later the same day or in the future. Reference staff can advise you in both how to fill out a call slip and when the item can be served.

To contact Reference staff in the Prints and Photographs Reading Room, please use our Ask A Librarian service or call the reading room between 8:30 and 5:00 at 202-707-6394, and Press 3.

Cite This Item

Citations are generated automatically from bibliographic data as a convenience, and may not be complete or accurate.

Chicago citation style:

Historic American Engineering Record, Creator, State Of Arkansas, University Of Arkansas, and Elam Denham. Woolsey Bridge, County Road , Woolsey, Washington County, AR. Washington County Woolsey Arkansas, 1968. Documentation Compiled After. Photograph. https://aj.sunback.homes/item/ar0135/.

APA citation style:

Historic American Engineering Record, C., State Of Arkansas, University Of Arkansas & Denham, E. (1968) Woolsey Bridge, County Road , Woolsey, Washington County, AR. Washington County Woolsey Arkansas, 1968. Documentation Compiled After. [Photograph] Retrieved from the Library of Congress, https://aj.sunback.homes/item/ar0135/.

MLA citation style:

Historic American Engineering Record, Creator, et al. Woolsey Bridge, County Road , Woolsey, Washington County, AR. Documentation Compiled After. Photograph. Retrieved from the Library of Congress, <aj.sunback.homes/item/ar0135/>.