Book/Printed Material Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for turning and finishing every description of watch pivots, pinions, staffs &c ...
-
Image 1 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … 2 ee DIRECTIONS FOR USING BOTT UMS PATENT IMPROVED UNIVERSAL LATHE CHUCKS AND IMPROVED LATHES FOR TURNING AND FINISHING EVERY DESCRIPTION OF WATCH PIVOTS PINIONS STAFFS c 7 _ uu me ALSO…- Contributor: Bottum, James M.
- Date: 1852
-
Image 2 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for …- Contributor: Bottum, James M.
- Date: 1852
-
Image 3 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … DIRECT TONS FOR USING POLE MS Po ae NOP IM PROV ED UNeL VERS AL LATHE CHUCKS AND O74 IMPROVED LATHES FOR TURNING AND FINISHING EVERY DESCRIPTION OF WATCH PIVOTS PINIONS STAFFS…- Contributor: Bottum, James M.
- Date: 1852
-
Image 4 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … Entered according to Act of Congress in the year 1852 by Jamzs M Borrum irs Bh the Clerks Office of the District Court for the Southern District of New York a eee…- Contributor: Bottum, James M.
- Date: 1852
-
Image 5 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … PREFACE Tue following pages are not as complete jin all respects as could be desired yet they are believed to contain every thing necessary for the practical workman for whose use they…- Contributor: Bottum, James M.
- Date: 1852
-
Image 6 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for …- Contributor: Bottum, James M.
- Date: 1852
-
Image 7 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … DIREC T1ONS Fiqure 1 FicureE 1 is a side view of the Improved Universal Lathe designed more particularly for watchmakers use It is so constructed as to run with the least possible…- Contributor: Bottum, James M.
- Date: 1852
-
Image 8 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … 6 nient to use much cement The Chuck A is to be carefully turned and centred at a as shown in the figure the hollow tube 6 should be made to slide…- Contributor: Bottum, James M.
- Date: 1852
-
Image 9 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … 7 to be heated by the lamp until it will melt the cement when applied to the end when a sufficient quantity is melted on the Chuck the cylinder is to be…- Contributor: Bottum, James M.
- Date: 1852
-
Image 10 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … 8 piece of wood cut into convenient shape should be used as shown in the figure it should also be used for chucking every description of work and in all cases the…- Contributor: Bottum, James M.
- Date: 1852
-
Image 11 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … 9 Figure 11 Fig 11 represents a boxwood Chuck secured to the brass Chuck d and the hollow e in the wood is to be turned as shown in the figure and…- Contributor: Bottum, James M.
- Date: 1852
-
Image 12 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … 10 of Chuck can be used for chronometer rollers duplex pallets table rollers hollow pinions c by converting the steel centre piece into an arbor Figure 14 Fig 14 is a Chuck…- Contributor: Bottum, James M.
- Date: 1852
-
Image 13 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … 11 and oil conical pivots may be rapidly finished directly from the graver A piece of watchwood may be used for clean ing the pivot after using the wheel Figure 18 Fig…- Contributor: Bottum, James M.
- Date: 1852
-
Image 14 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … 12 the same thickness as the spring should be cemented on the wheel with it as in No 2 When screw heads are to be finished holes should be made for the…- Contributor: Bottum, James M.
- Date: 1852
-
Image 15 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … 13 Figure 24 Fig 24 shows a plate for making and finishing flat sur faces Nos 1 and 2 are the adjusting screws which can be used to bring the surface of…- Contributor: Bottum, James M.
- Date: 1852
-
Image 16 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … 14 it is to be held to turn the piece c When it cuts more deeply than is required move the point towards A instead of c If held as represented in…- Contributor: Bottum, James M.
- Date: 1852
-
Image 17 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … 15 and a small iron rod used to connect the footpiece with the crank It should be secured to the footpiece by a staple and to the crank by a hook on…- Contributor: Bottum, James M.
- Date: 1852
-
Image 18 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … 16 be drilled and a piece of steel driven into the hole and the pivot turned and finished without being removed from the Chuck The larger drills may be cemented in Chucks…- Contributor: Bottum, James M.
- Date: 1852
-
Image 19 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … 17 Figs 1 2 3 4 4 beam SS- Contributor: Bottum, James M.
- Date: 1852
-
Image 20 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for …- Contributor: Bottum, James M.
- Date: 1852
-
Image 21 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … 19 Fig 5 Fig Fig 8 Fig 7 Fig 11 Fig 10- Contributor: Bottum, James M.
- Date: 1852
-
Image 22 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for …- Contributor: Bottum, James M.
- Date: 1852
-
Image 23 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … 4 lf Ul Fig 22 Fig 21- Contributor: Bottum, James M.
- Date: 1852
-
Image 24 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for …- Contributor: Bottum, James M.
- Date: 1852
-
Image 25 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for …- Contributor: Bottum, James M.
- Date: 1852
-
Image 26 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for …- Contributor: Bottum, James M.
- Date: 1852
-
Image 27 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for …- Contributor: Bottum, James M.
- Date: 1852
-
Image 28 of Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for … LIBRARY OF CONGRESS- Contributor: Bottum, James M.
- Date: 1852
About this Item
Title
- Directions for using Bottum's patent improved universal lathe chucks and improved lathes, for turning and finishing every description of watch pivots, pinions, staffs &c ...
Names
- Bottum, James M. [from old catalog]
Created / Published
- New York, Printed by Hart & Holden, 1852.
Headings
- - Clock and watch making--Machinery
- - Lathes
Notes
- - Also available in digital form.
Medium
- 23 p. incl. plates. 18 cm.
Call Number/Physical Location
- TS546 .B75
Library of Congress Control Number
- 08030319
Online Format
- online text
- image